Skip to main content

Mechanical Engineering Review Materials: PSME Code (With Answer)

As promised on the previous articles, I prepared some materials for the upcoming Mechanical Engineering Board Exam. I hope this one will help.


Update: Answers in red.

Questions from the Philippine Mechanical Code (PSME Code)

1. As a requirement for permit application, for any installation involving machine, mechanical equipment, general layout plan for each floor drawn should not be less than
a. 1:200 b. 1:500 c. 1:1000 d. 1:100

2. Standard sheet sizes for mechanical plans and drawings shall be based on a width to length ratio of
a. 1: sqrt (2) b. 1:sqrt(3) c. 1:3 d. 1:2

3. For commercial and industrial buildings, work rooms (referring to maintenance shop and machine room) shall be at least _______ height from floor to ceiling.
a. 3 000 mm b. 2 000 mm c. 5 000 mm d. 4 000 mm

4. For guyed steel stacks, the angle between the stack and guy wire is usually
a. 30º b. 45 º c. 60 º d. 75 º

5. It is a heavy wheel which by its inertia assists in securing uniform motion of machinery by resisting sudden changes of speed.
a. cartwheel b. flywheel c. motor d. shaft





6. The extension of piston rod passing through a stuffing box in the outside area of an engine cylinder, compressor cylinder or pump cylinder.
a. tail rod b. pin c. hub d. sprocket

7. Type A sprocket has
a. one hub c. no hub
b. two side hubs d. bolted hubs

8. The reciprocating machine part within a cylinder is called
a. ram c. slide mandrel
b. plunger d. all of the above

9. Fixed-mounted or movable hood guards covering the length of run of power chains.
a. coupling guards c. belt guards
b. chain guards d. hood guards

10. A boom type mobile crane mounted on endless tracks or thread belts.
a. gantry crane c. locomotive crane
b. jib crane d. crawler crane

11. A mechanical contrivance for raising or lowering a load.
a. crane b. hoist c. rope d. chain

12. A horizontal arm for supporting a trolley or fall blocks which does not change its inclination with the horizontal.
a. clevis b. boom c. hood d. jib

13. One hand signal for crane movement arm extended, palm down, hold position rigidly.
a. stop b. lower c. hoist d. swing boom

14. Two hand signal for crane movement hold both arms horizontally at sides fully extend and move upward & return.
a. stop b. lower c. hoist d. swing boom

15. In elevator systems, a device designed to stop a descending car or counterweight beyond its lowest limit of travel.
a. bumper b. buffer c. dumbwaiter d. hoist way

16. The minimum factor of safety for suspension wire rods with 1 500 feet per min (fpm) passenger elevator.
a. 7.6 b. 9.5 c. 10 d. 11.9

17. A closed vessel in which steam or vapor is generated at a pressure of more than 1.055 kg/cm2 gage by direct application of heat.
a. portable boiler c. locomotive boiler
b. miniature boiler d. power boiler

18. Method of testing boiler integrity that uses x-rays to generate & record on film the imperfections or defects in the boiler tube material & welds.
a. metallurgical replication c. vacuum testing
b. ultrasonic thickness gauging d. radiographic testing

19. In the fire protection, class of fire in ordinary combustible materials such as cloth paper, rubber & many plastics.
a. Class A b. Class B c. Class C d. Class D

20. An underground formation that contains sufficient saturated permeable material to yield significant quantities of water.
a. aquifer b. water table c. porous layer d. well

21. Pipe color for acetylene.
a. yellow b. green c. orange d. red

22. In metrology, it is a device used to determine whether the part has been made to the tolerance required and does not usually indicates a specific dimension.
a. bevels c. gage
b. dial indicator d. trammel

23. In manufacturing, process of making molds for the plastic and die casting industries.
a. intraforming c. infiltration
b. swaging d. hobbing

24. A copper-silicon alloy available in five slightly different nominal compositions for applications which require high strength, good fabricating, & fusing qualities.
a. inconel c. everdur
b. monel d. babbit

25. In instrumentation, it is a device whose function is to pass on information in an unchanged form or in some modified form.
a. programmable logic controller (PLC) c. pilot light
b. controller d. relay

SOURCE: THE PHILIPPINE MECHANICAL CODE (FORMERLY PSME CODE) CODE 2003 EDITION

More mechanical engineering board exam review materials on the succeeding posts. Please subscribe to receive alerts whenevel new reviewers are posted.

Reblog this post [with Zemanta]

Comments

  1. Nice blog of Mechanical Engineering.
    Cranes are used commonly in construction/ manufacturing industry. These are temporary structures, and is either fixed or mounted.

    larry

    ReplyDelete
    Replies
    1. hi, how can i join this stuff? you know please send me other review materials for ME, here's my email...desquitado_j@yahoo.com

      thanks a lot god bless.

      Delete
  2. This is one informative blog for mechanical engineering enthusiasts. Relay is an electrically operated switch. In modern electric power systems these functions are performed by digital instruments still called "protective relays".

    ReplyDelete
  3. ive been in practice for almost 40 years sa mechanical engneering - the likes of turbo-machineries, pressure vessel, heaters, heat exchanger to name a few. Hold a PME license in the early 80s.

    Currently work outside the country in petrochem for a very very long time. Can i post in your blog related to the work i been involved with concerning heavy mechanical works.

    ReplyDelete
  4. Sure...can you please send me an email so I can grant you access to this blog?

    My email address is admin@tupmechanical.com

    ReplyDelete
  5. Please send me some review materials that comes out in ME Board Exam. Here is my e-mail address anacletoclarogemida@yahoo.com

    ReplyDelete
  6. THE PHILIPPINE MECHANICAL CODE (FORMERLY PSME CODE) CODE 2003 EDITION
    sir san makakabili nito po?

    ReplyDelete
  7. sir pa email nman po ako kung saan makakabili or free download nito.THE PHILIPPINE MECHANICAL CODE (FORMERLY PSME CODE) CODE 2003 EDITION
    magtake po kasi ako ng board sa march.
    maraming salamat po.
    email add ko.rommel_ky031404@yahoo.com

    ReplyDelete
  8. This comment has been removed by the author.

    ReplyDelete
  9. sir pa email din po sa mail ko ng copy ng "PHILIPPINE MECHANICAL CODE (FORMERLY PSME CODE) CODE 2003 EDITION", or kahit ung picture lang po ng book kasama ung author, para po makabili ako. magtake po ako ng board exam sa march..tnx po
    shin_napier@yahoo.com po mail ko

    ReplyDelete
  10. sir whose the author of the book??

    ReplyDelete
  11. Sir balak ko po mag exam sa 2016 nasa middle east po ako pwede po bang pa share ng ME review materials

    ReplyDelete
  12. Sir balak ko rin po na mag exam sa 2016...pwede po makahingi ng ME review materials, at ilang ME reviewer? ito po yung email ko peligropetronillo@yahoo.com....... salamat po sa mga magbibigay

    ReplyDelete
  13. sir pa email din po sa mail ko ng copy ng "PHILIPPINE MECHANICAL CODE (FORMERLY PSME CODE) CODE 2003 EDITION", eto email ko: framos@alessa.com.sa ,,,mag self review lang ako dito sa riyadh... salamat po.

    ReplyDelete
  14. sir, can I ask also a copy of ""PHILIPPINE MECHANICAL CODE (FORMERLY PSME CODE) CODE 2003 EDITION".... e-mail add: drazensalunga@yahoo.com... for self study... Thanks in advance.

    ReplyDelete
  15. sir pwede po ba maka hingi copy ng PHILIPPINE MECHANICAL CODE (FORMERLY PSME CODE) CODE 2003 or 2012, ito po email ko jek21_potm@yahoo.com salamat po

    ReplyDelete
  16. I am looking for the latest edition/version of PSME Code. Please help

    ReplyDelete
  17. Good day sir.pwede po makahingi ng old or latest edition ng PSME code.?please email to my email acct. saliliedgardo@yahoo.com.. Thank you for the response.

    ReplyDelete
  18. Good day sir.pwede po makahingi ng old or latest edition ng PSME code.?please email to my email acct. mbl_0504@yahoo.com.. Thank you for the response.

    ReplyDelete
  19. Good day sir.pwede po makahingi ng old or latest edition ng PSME code.?please email to cedricdaryll@yahoo.com

    ReplyDelete
  20. pa email naman po ng review materials. thank you
    mr.lowendurante@gmail.com

    ReplyDelete
  21. Sir good day! Pwede po ba pa email ng psme code. Magtake po kasi ako ng SPLBE sa middle east need lang po ng reviewer and pointers sa exam. Thank you in advanced. This is my email address: c_gayol@yahoo.com

    ReplyDelete
  22. sir penge po copy ng pme code thanks in advance trueco2nut05@gmail.com

    ReplyDelete
  23. This comment has been removed by the author.

    ReplyDelete
  24. sir penge po details ng PSME Code kung sino po ung author para makabili po thank you po ito po email ko. aronjamesempig@gmail.com

    ReplyDelete

Post a Comment

Popular posts from this blog

BOARD EXAM TIP: Which Review Center?

First of all, I would like to apologize for a long time I haven't posted anything but introduction. The reason for that is I'm busy optimizing the design of this site. I'm hoping that the make over is good. Anyway, I would like to dedicate this article to those who are going to take/retake the board exam this coming October. My sincere wish that you bring out the best among yourselves and may the deserving ones pass the exam.




Going back to the One-Million-Peso worth question: "Which review center should I enroll?", I would like to answer that in the most unbiased way I can. Of course, I'm only human and I had also my preferences but I will try my best to hide it.

To start with I will enumerate some of the prominent review centers that offer board exam reviews for mechanical engineering in the Philippines.

1. Alcorcon (Cebu & Manila)
2. Excel (Cebu & Manila)
3. Linx Engineering (Manila)
4. MERIT (Manila)
5. PRIME (Cebu)
6. RLB's CDTC (Manila)
I'…

PAST MECHANICAL BOARD EXAM QUESTION: Machine Design Set-1 (solutions and answers)

The following are the solutions and answers to MODIFIED PAST MECHANICAL BOARD EXAM QUESTION: Machine Design Set-1 posted on this blog last Saturday, November 14, 2009.




Again, I want to stress out that most of the questions here are modified from its original form for the purpose of improving the question.

Past Mechanical Engineering Board Exam Question Number 1
A 4 inches diameter short shaft carrying 2 pulleys close to the bearings transmits how much horsepower if the shaft makes 120 rpm.

A.200HP               B. 199 HP

C.198 HP              D. 202 HP

P = (D3N )/38 -- for mula for short shafts from PSME code

P = (4)3(120)/38

P= 202 HP

Past Mechanical Engineering Board Exam Question Number 2
An instrument that measures the hardness of the work piece in terms of elasticity.

a. Durometer

b. Scleroscope

c. Mohs's Scale

d. Brinell Tester

Source: Machinery’s Handbook

SOLUTION TO MECHANICAL BOARD EXAM PROBLEMS: Power Set-1

Here are the solutions to board problems given at Power Subject Set-1. If you do not understand anything, feel free to write a comment voicing out your concern. I'm still looking for better ways to present my solution. I still don't know how to present equations and mathematical symbols with blogger. Please bear with me.

1. An automobile tire is inflated to 32psig pressure at 50 degree F. After being driven, the temperature rises to 75 degree F. Determine the final gage pressure assuming the volume remains constant. (Electrical Engineering Board Exam Problem)

Solution:
Since volume is constant, use Charles’ Law on constant volume processes.
P1/T1=P2/T2
Note: P and T should be absolute.

(32+14.7)/ (50+460) =P2/ (75+460)

P2=48.99 psia

Converting back to gage pressure,

P2g=48.99-14.7

P2g=34.29 psig


2. Four hundred cubic centimeters of gas at a pressure of 740 mmHg absolute and temperature of 18 degree C undergoes a process until the pressure and temperature becomes 760 mmHg abso…