Skip to main content

Mechanical Engineer Board Exam Result March 2010

By Admin
The Professional Regulation Commission (PRC) successfully administered the March 2010 Mechanical Engineering board examination to the qualified examinees. It was held last Saturday and Sunday, March 27 and 28 respectively. This new schedule is actually a month earlier than the previous one. The exam is divided into three main categories or topics, Mathematics (Economy, Laws, and Engineering Sciences), Machine Design (and machine Shop Practices), and Power (Power and Industrial Plant Engineering).

The board of mechanical engineering (BME), as directed by RA 8495 or The Philippine Mechanical Engineering Act of 1998, is the sole body in-charge of making the exam questionnaires. This year’s board members are the following.

Alfredo Y. Po (Chairman)
Vicente B. Vosotros (Member)
Leandro A. Conti (Member)

Result of the Mach 2010 Mechanical Engineer Board Exam

The result is yet to be released. Upon the release of the list of passers and topnochers, it will be immediately posted in this blog, www.tupmechanical.blogspot.com. Please stay tune!

Meanwhile, you can subscribe to our email list below. You will be notified upon the arrival of the board exam results.



Important! Please take note that you should activate your subscription by clicking the link sent to your email address.
Labels:

Comments

Post a Comment

Popular posts from this blog

PAST MECHANICAL BOARD EXAM QUESTION: Machine Design Set-1 (solutions and answers)

By Admin
The following are the solutions and answers to MODIFIED PAST MECHANICAL BOARD EXAM QUESTION: Machine Design Set-1 posted on this blog last Saturday, November 14, 2009. Again, I want to stress out that most of the questions here are modified from its original form for the purpose of improving the question. Past Mechanical Engineering Board Exam Question Number 1 A 4 inches diameter short shaft carrying 2 pulleys close to the bearings transmits how much horsepower if the shaft makes 120 rpm. A.200HP               B. 199 HP C.198 HP               D. 202 HP P = (D3N )/38 -- for mula for short shafts from PSME code P = (4)3(120)/38 P= 202 HP Past Mechanical Engineering Board Exam Question Number 2 An instrument that measures the hardness of the work piece in terms of elasticity. a. Durometer b. Scleroscope c. Mohs's Scale d. Brinell Tester Source: Machinery’s Handbook
22 comments
Read More...

SOLUTION TO MECHANICAL BOARD EXAM PROBLEMS: Power Set-1

By Admin
Here are the solutions to board problems given at Power Subject Set-1. If you do not understand anything, feel free to write a comment voicing out your concern. I'm still looking for better ways to present my solution. I still don't know how to present equations and mathematical symbols with blogger. Please bear with me. 1. An automobile tire is inflated to 32psig pressure at 50 degree F. After being driven, the temperature rises to 75 degree F. Determine the final gage pressure assuming the volume remains constant. (Electrical Engineering Board Exam Problem) Solution: Since volume is constant, use Charles’ Law on constant volume processes. P1/T1=P2/T2 Note: P and T should be absolute. (32+14.7)/ (50+460) =P2/ (75+460) P2=48.99 psia Converting back to gage pressure, P2g=48.99-14.7 P2g=34.29 psig 2. Four hundred cubic centimeters of gas at a pressure of 740 mmHg absolute and temperature of 18 degree C undergoes a process until the pressure and temperature be
8 comments
Read More...

BOARD EXAM TIP: Which Review Center?

By Admin
First of all, I would like to apologize for a long time I haven't posted anything but introduction. The reason for that is I'm busy optimizing the design of this site. I'm hoping that the make over is good. Anyway, I would like to dedicate this article to those who are going to take/retake the board exam this coming October. My sincere wish that you bring out the best among yourselves and may the deserving ones pass the exam. Going back to the One-Million-Peso worth question: "Which review center should I enroll?" , I would like to answer that in the most unbiased way I can. Of course, I'm only human and I had also my preferences but I will try my best to hide it. To start with I will enumerate some of the prominent review centers that offer board exam reviews for mechanical engineering in the Philippines. 1. Alcorcon (Cebu & Manila) 2. Excel (Cebu & Manila) 3. Linx Engineering (Manila) 4. MERIT (Manila) 5. PRIME (Cebu) 6. RLB's
105 comments
Read More...