Skip to main content

Mechanical Engineer Board Exam November 2010 (Middle East)

Here's the list of passers in the Board Exam for Mechanical Engineers given by the Board of Mechanical Engineering in the Middle East last November 2010.


Roll of Successful Examinees in the
PROFESSIONAL MECHANICAL ENGINEER EXAMINATION
Held in November 2010
Released on December 9, 2010
SEQ. NO. N A M E
1 BETON, JOSE JR BROTARLO
2 BONGOLTO, ARTURO GULDE
3 CRUZ, PETRONILO SUBA
4 GARCIA, RANDY EBALLAR
5 GOMESERIA, RONALD VALLEDOR
6 GONZALES, SIMEON JR CABILLAN
7 GUZMAN, PLACIDO CABALFIN
8 HEREZO, NELSON SUERTE
9 JARAMILLA, LENUEL PAJUELAS
10 KHAN, FLAVIO VILLANUEVA
11 MOYANO, ALAN DELA TORRE
12 ONGOCO, ARTURO JR SADURAL
13 PANGILINAN, MANUEL MUNSOD
14 PARDILLA, ARISTOTLE PALOMILLO
15 PASUELO, NARCISO MAGBANUA
16 PEDROZO, REYNALDO DELA CRUZ
17 PELAEZ, PORFERIO ILISAN
18 PEREZ, BENITO AGUSTIN
19 PORTE, JOEY MICHAEL PEÑA
20 ROMANES, BERNARDO CARAAN
21 SEVA, ROMEO JR PEDRAJAS
22 SOMIDO, ROWELL GATDULA
23 VALENZUELA, LEVI ORTIGUERRA
NOTHING FOLLOWS----------------------

Roll of Successful Examinees in the
MECHANICAL ENGINEER BOARD EXAMINATION - MIDDLE EAST
Held on NOVEMBER 16 & 17, 2010
Released on DECEMBER 9, 2010
Seq. No. N a m e
1 BANSIL, WILZON LUGTU
2 BARBOSA, RUEL BALON
3 BARRIOS, BIENVENIDO JR BENOZA
4 BATTUNG, JOMAR TURINGAN
5 CABREROS, JAYSON PEDROZA
6 CASTILLO, ROBBIE PUNAY
7 CERIBO, MARVIN LOPENA
8 DAYAWAN, MARIO JR GALLETO
9 DE GUZMAN, LEONARDO JR CRUZ
10 DE VILLA, PAULINO CARSOCHO
11 ECONAR, LEANTHONY DABLIO
12 ELARDO, LEONARDO BANTANG
13 ESPINOSA, JOVEN BACALAN
14 FLORES, HELBERT HYBO
15 GAMINO, MICHAEL HIPOLITO
16 GATCHALIAN, ELMER ECHEM
17 LLAMAS, REY JULIUS CAESAR BOBILES
18 MANANSALA, DENNIS TEODOCIO
19 MENDOZA, ROMEL SARMIENTO
20 OCAMPO, ERWIN QUIZON
21 OCATE, HERNANIE CANILLA
22 PONFERRADA, DOMINADOR JR ALVARAN
23 QUINDICA, JOEMEL OBISPO
24 SAINZ, JORDAN PANGAN
25 SAMSON, DIEGO LASULA
26 SAPITULA, HERNAND ALMODOVAR
27 SILADOR, CARLITO ALFORQUE
28 VILLACERAN, LINDON OFIANGA
29 VILLANUEVA, CHRISTOPHER OCA
NOTHING Follows_____________

MECHANICAL ENGINEER BOARD EXAMINATION - MIDDLE EAST
Held on NOVEMBER 16 & 17, 2010
Released on DECEMBER 9, 2010
List of successful examinees whose REGISTRATION shall be DEFERRED
pending compliance with some registration requirements:
Seq. No. N a m e
1 ACOSTA, LIZA LUMANGLAS
2 AMOSCO, ANTONIO JR HIZOLE
3 ARENAS, ORLANDO REYES
4 BADAYOS, ROLANDO JR AMOLONG
5 BASTIDA, GLEEN FERNANDEZ
6 BERSABE, GERRIC PAGUO
7 DE LEON, JOHN ELEUTERIO
8 PADILLA, PETER DIZON
9 ZABLAN, REYNANTE AMBOY
NOTHING FOLLOWS.......................

Source: PRC

Comments

  1. Galvanized steel is steel that has been hot dipped in a pool of molten zinc. The zinc adheres to the steel, cools and hardens to form a rust inhibitive finish to plain steel.

    ReplyDelete

Post a Comment

Popular posts from this blog

BOARD EXAM TIP: Which Review Center?

First of all, I would like to apologize for a long time I haven't posted anything but introduction. The reason for that is I'm busy optimizing the design of this site. I'm hoping that the make over is good. Anyway, I would like to dedicate this article to those who are going to take/retake the board exam this coming October. My sincere wish that you bring out the best among yourselves and may the deserving ones pass the exam.




Going back to the One-Million-Peso worth question: "Which review center should I enroll?", I would like to answer that in the most unbiased way I can. Of course, I'm only human and I had also my preferences but I will try my best to hide it.

To start with I will enumerate some of the prominent review centers that offer board exam reviews for mechanical engineering in the Philippines.

1. Alcorcon (Cebu & Manila)
2. Excel (Cebu & Manila)
3. Linx Engineering (Manila)
4. MERIT (Manila)
5. PRIME (Cebu)
6. RLB's CDTC (Manila)
I'…

PAST MECHANICAL BOARD EXAM QUESTION: Machine Design Set-1 (solutions and answers)

The following are the solutions and answers to MODIFIED PAST MECHANICAL BOARD EXAM QUESTION: Machine Design Set-1 posted on this blog last Saturday, November 14, 2009.




Again, I want to stress out that most of the questions here are modified from its original form for the purpose of improving the question.

Past Mechanical Engineering Board Exam Question Number 1
A 4 inches diameter short shaft carrying 2 pulleys close to the bearings transmits how much horsepower if the shaft makes 120 rpm.

A.200HP               B. 199 HP

C.198 HP              D. 202 HP

P = (D3N )/38 -- for mula for short shafts from PSME code

P = (4)3(120)/38

P= 202 HP

Past Mechanical Engineering Board Exam Question Number 2
An instrument that measures the hardness of the work piece in terms of elasticity.

a. Durometer

b. Scleroscope

c. Mohs's Scale

d. Brinell Tester

Source: Machinery’s Handbook

SOLUTION TO MECHANICAL BOARD EXAM PROBLEMS: Power Set-1

Here are the solutions to board problems given at Power Subject Set-1. If you do not understand anything, feel free to write a comment voicing out your concern. I'm still looking for better ways to present my solution. I still don't know how to present equations and mathematical symbols with blogger. Please bear with me.

1. An automobile tire is inflated to 32psig pressure at 50 degree F. After being driven, the temperature rises to 75 degree F. Determine the final gage pressure assuming the volume remains constant. (Electrical Engineering Board Exam Problem)

Solution:
Since volume is constant, use Charles’ Law on constant volume processes.
P1/T1=P2/T2
Note: P and T should be absolute.

(32+14.7)/ (50+460) =P2/ (75+460)

P2=48.99 psia

Converting back to gage pressure,

P2g=48.99-14.7

P2g=34.29 psig


2. Four hundred cubic centimeters of gas at a pressure of 740 mmHg absolute and temperature of 18 degree C undergoes a process until the pressure and temperature becomes 760 mmHg abso…