Skip to main content

Posts

TUP Manila Grad Tops March 2012 Mechanical Engineer Board Exam

Technological University of Philippines (TUP)- Manila has every reason to rejoice since two of their Mechanical Engineering graduates was listed among the top 10 students in the recently held board exam for Mechanical Engineers.

Engineer Victor Buan Valdez bested all examinees by scoring the highest with 92.85%. On the third spot is another TUP Manila stud in the name of Bryan Tejana Castro scoring 91.80%.

A Mapua Institute of Technology (MIT) grad captures the second spot while five University of Cebu (UC) and two Batangas University (BatSU) grads completes the top 10 list.

 650 out of 1,089 passes the Registered Mechanical Engineer Exam, 26 out of 50 in the Certified Plant Mechanic (CPM) and 23 passed the Technical Evaluation for the Upgrading as Professional Mechanical Engineer. The semi-annual licensure exam administered by the Professional Regulation Commission was held last week.

The top 10 list is shown below:

1 VICTOR BUAN VALDEZ   - TECHNOLOGICAL UNIVERSITY OF THE PHILIPPINES…
Recent posts

Results of Mechanical Engineer Board Exam on Middle East - December 2011

The Professional Regulation Commission (PRC) announces that 31 out of 98 passed the Mechanical Engineer Board Examination given by the Board of Mechanical Engineering in the cities of Abu Dhabi, United Arab Emirates; Jeddah and Riyadh, Kingdom of Saudi Arabia and in Doha, Qatar this December 2011.  

The following are the list of passers:
MECHANICAL ENGINEER BOARD EXAMINATION - MIDDLE EAST

Held on DECEMBER 9 and 10, 2011
Released on DECEMBER 22, 2011

Seq. No. N a m e

1 AUSTRIA, ROWEL ATIENZA
2 CATAYLO, ROBCHAR DAYOCOS
3 DE LA PAZ, RAMIL PABON
4 DIÑO, LOUIE JIONGCO
5 DURANTE, ROGELIO ALBARIDA
6 FLORIDO, MARCELO III CADUNGOG
7 FORTUS, ABBE PHAROAH ARIAS
8 HERNANDO, SCHUBERT LANGBID
9 JUNSAY, ROSELLER JR ABION
10 LEYVA, ROMMEL ROGUEL
11 MACASA, JACKSON BAGON
12 MAGNETICO, JOEL QUERO
13 MALANG, DEXTER ALLAN CARAIG
14 MORDIDO, WILLIAM MANA
15 OPLADO, ROMEO TUDTUD
16 ORA, ANTHONY BALACUIT
17 PABLO, IAN LINUS LIBRE
18 PALCE, NICASIO JR PEÑALOSA
19 PALTINGCA, NICO CANOY
20 PANGANGAAN, JOSEPH VILLAR
21 PUGOY, JOECH…

TOP 10 Mechanical Engineers Board Exam March 2011

The following are the top 10 RME examinees in March 2011 Mechanical Engineer Board Exam
1 OLIVER MANGOBA REVALO - MAPUA INSTITUTE OF TECHNOLOGY - 91.60
2 MARK LOYD MARFA BAYA - MINDANAO STATE UNIVERSITY- MARAWI CITY - 91.5
3 MIGUEL CABRAL YAP - TECHNOLOGICAL UNIVERSITY OF THE PHILIPPINES-MANILA - 90.5
4 GROMYKO TAN GERALDINO JR - UNIVERSITY OF SAN CARLOS - 89.85
5 RAYMOND ALCORIZA DELA CRUZ - BULACAN STATE UNIVERSITY (FOR.BCAT)-MALOLOS - 89.5
6 GERWIN PACINIO DESQUITADO - CEBU INSTITUTE OF TECHNOLOGY - 88.60
7 RALPH LAWRENCE GO KUA MAPUA INSTITUTE OF TECHNOLOGY - 88.25
8 JOEL FESTEJO JORBAN - MINDANAO STATE UNIVERSITY - MARAWI CITY - 87.6
9 JOSEPH KARL PARAS CONTENTO - UNIVERSITY OF SAN CARLOS - 87.55
10 JINO KARLO ASIS RIVERA - UNIVERSITY OF THE PHILIPPINES- DILIMAN - 87.2
 NOTHING FOLLOWS--------------------------

MARCH 2011 MECHANICAL ENGINEER BOARD EXAM RESULT

The Professional Regulation Commission (PRC) announces that 658 out of 1,220 passed the Mechanical Engineer Licensure Examinations given by the Board of Mechanical Engineering in Manila and Cebu this March 2011.

Roll of Successful Examinees in the 
PROFESSIONAL MECHANICAL ENGINEER BOARD EXAMINATION 
Held in MARCH 2011 
Released on MARCH 21, 2011

1 ABASOLO, ROLANDO OCARIZA 
2 ALTEZA, VIRGILIO ANTONIO LEGASPI 
3 BEJA, ELVIN BAGAIPO 
4 CAGO, ROLANDO AMOLONG 
5 CASTILLO, RONNEL DE LEON 
6 CAÑETE, ROLANDO PONCE 
7 CIRUJALES, EDWIN CEREZA 
8 COMINGUEZ, RICARDO JR CLEOFE 
9 DACIR, RANULFO CORNELIO 
10 DAVANTES, FORTUNATO JR RECOLCOLIN 
11 DESIDERIO, FERNANDO PAULO ADORABLE 
12 GONZALES, ARNEL PAGSISIHAN 
13 LAO, LEONARDO DIAZ 
14 MONTOLO, CESAR CABRERA 
15 NACPIL, LEVY VENZON 
16 NERI, ANTHONY DUMAUG 
17 OLIVARES, ERWIN PORTUGAL 
18 PAELDEN, ANDRONICO JR BARIENTOS 
19 PAPA, RICARDO PAREDES 
20 SIA, SIEGFRIED GODINEZ
NOTHING FOLLOWS-----------------

Roll of Successful Examinees in the 
MECHANICAL ENGINEER BOAR…

Answers to ME Review Questions in Strength of Materials

Answers to the questions on Strength of Materials.
1. In the cross section of a shaft subjected to torsion, the stress is maximum at what location?
C. At the surface of the shaft
- The shear stress increases from the center (zero stress) to the outer(maximum stress).
- Application: Hollow shaft is a good replacement for solid shaft since only the less stressed portion (the center) is removed.

2. The stress experienced by a body under torsion is…
A. Shear stress

3. The stress experienced by a pressurized vessel is…
C. Tensile stress
-pressure tends to pull (tension) the shell of the vessel

4. The “Maximum Shear Theory”, one of the known theories of failure is also known as…
B. Guest’s theory

5. In the stress-strain curve, it is the point at which there is an appreciable elongation without corresponding increase in load.

D. Yield point

6. What will happen to the stress in a shaft under torsion if the diameter was decreased to half the original?
C. The stress will be increased eightfold
-stre…

ME Review: Strength of Materials

Instruction: Choose the BEST answer.

1. In the cross section of a shaft subjected to torsion, the stress is maximum at what location?
a. Near the center of the shaft
b. Between the surface and the center of the shaft
c. At the surface of the shaft
d. The stress is uniform from center to surface of the shaft

2. The stress experienced by a body under torsion is…
a. Shear stress
b. Compressive stress
c. Tensile stress
d. Bending stress

3. The stress experienced by a pressurized vessel is…
a. Shear stress
b. Compressive stress
c. Tensile stress
d. Bending stress

4. The “Maximum Shear Theory”, one of the known theories of failure is also known as…
a. Mises Yield theory
b. Guest’s theory
c. Venant theory
d. Rankine Theory

5. In the stress-strain curve, it is the point at which there is an appreciable elongation without corresponding increase in load.
a. Elastic limit
b. Rupture strength
c. Proportional limit
d. Yield point

6. What will happen to the stress in a shaft under torsion if the d…

Mechanical Engineer Board Exam November 2010 (Middle East)

Here's the list of passers in the Board Exam for Mechanical Engineers given by the Board of Mechanical Engineering in the Middle East last November 2010.

Roll of Successful Examinees in the PROFESSIONAL MECHANICAL ENGINEER EXAMINATION Held in November 2010 Released on December 9, 2010 SEQ. NO. N A M E 1 BETON, JOSE JR BROTARLO 2 BONGOLTO, ARTURO GULDE 3 CRUZ, PETRONILO SUBA 4 GARCIA, RANDY EBALLAR 5 GOMESERIA, RONALD VALLEDOR 6 GONZALES, SIMEON JR CABILLAN 7 GUZMAN, PLACIDO CABALFIN 8 HEREZO, NELSON SUERTE 9 JARAMILLA, LENUEL PAJUELAS 10 KHAN, FLAVIO VILLANUEVA 11 MOYANO, ALAN DELA TORRE 12 ONGOCO, ARTURO JR SADURAL 13 PANGILINAN, MANUEL MUNSOD 14 PARDILLA, ARISTOTLE PALOMILLO 15 PASUELO, NARCISO MAGBANUA 16 PEDROZO, REYNALDO DELA CRUZ 17 PELAEZ, PORFERIO ILISAN 18 PEREZ, BENITO AGUSTIN 19 PORTE, JOEY MICHAEL PEÑA 20 ROMANES, BERNARDO CARAAN 21 SEVA, ROMEO JR PEDRAJAS 22 SOMIDO, ROWELL GATDULA 23 VALENZUELA, LEVI ORTIGUERRA NOTHING FOLLOWS----------------------
Roll of Successful Examinees in the MECHANICAL ENG…